®
BRAD NAILER / STAPLER
2-IN-1 KIT
Model 44923
ASSEMBLY AND OPERATION
INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2001, 2004 by Harbor FreightTools . All rights reserved. No
portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
8.
Use eye and ear protection. Always wear ANSI approved impact safety goggles
and appropriate hearing protection. Wear a full face shield if you are producing
metal filings or wood chips. Wear an ANSI approved dust mask or respirator
when working around metal, wood, and chemical dusts and mists. Other people
in the work area must also wear ANSI approved impact safety goggles.
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and air hoses
periodically and, if damaged, have them repaired by an authorized technician.The handle
must be kept clean, dry, and free from oil and grease at all times. Do not operate a tool if
any portion of the tool’s operating controls are inoperable, disconnected, altered or not
working properly.
10. Disconnect Air Hose and release any built-up air pressure. Never service the Nailer,
clear jams, or disassemble with the air hose attached. Always release any built-up air
even after disconnecting hose. Disconnect the Nailer when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are
removed from the tool or machine work surface before attaching to an air source.
12. Avoid unintentional starting. Be sure the trigger is in the Off position when not in use
and before plugging in. Do not carry any tool with your finger on the trigger, whether it is
attached to an air source or not. Do not point the tool towards yourself or anyone whether
it contains fasteners or not.
13. Stay alert. Watch what you are doing, use common sense.Do not operate any tool when
you are tired.
14. Check for damaged parts. Before using any tool, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment and binding of moving parts; any broken parts or mounting
fixtures;and any other condition that may affect proper operation.Any part that is damaged
should be properly repaired or replaced by a qualified technician. Do not use the tool if
the trigger does not operate properly.
15. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
16. Replacement parts and accessories. This product is to be repaired and serviced only
by a qualified technician. When this product is serviced, only identical replacement parts
should be used. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.
17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if
taking prescription medicine to determine if your judgement or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
18. Use proper size and type extension cord. If an extension cord is required, it must be of
the proper size and type to supply the correct current to the compressor without heating
up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage
to the tool. Check your air compressor’s manual for the appropriate size cord. It is also
possible that the use of an extension cord may cause your circuit breaker to trip or your
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 3
panel fuse to break. If this happens, either use the compressor without an extension
cord or find a larger amperage circuit to use.
19. Maintenance. The maintenance outlined in the maintenance section should be performed
regularly. For your safety, this product should be serviced or repaired regularly only by a
qualified technician.
20. Compressed air only. Never use combustible gas as a power source.
21.
Do not load nails with the trigger or safety depressed. Unintentional firing
may occur. Do not load nails when the air hose is connected to the tool. Always
assume that the tool contains fasteners.
22. Disconnect air supply before loading Nailer. Before reloading (or making any
adjustments to) the Nailer make sure that the compressed air is disconnected.
23. Fire fasteners into an appropriate work surface only. Do not attempt to fire fasteners
into surfaces too hard to penetrate. Do not drive fasteners on top of other fasteners, or at
too steep of an angle. Fasteners can ricochet causing personal injury. Never fire the
Nailer into the air, or point it toward yourself or another person. Always wear ANSI
approved safety goggles during use, maintenance, and reloading.
24. Do not fire fasteners too close to the edge of a workpiece. They may split the
workpiece and fly free, causing personal injury.
25. Take caution as some woods contain preservatives such as copper chromium
arsenate (CCA) which can be toxic. When stapling or nailing these materials extra
care should be taken to avoid inhalation and minimize skin contact.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities, contain chemicals known [to the State of California] to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other masonry products
• Arsenic and chromium from chemically treated lumber
(California Health & Safety Code 25249.5, et seq. )
26. Stay within air pressure capacity. Never operate the Nailer above 100 PSI.
27. Hold tool away from head and body. During operation the Nailer may kick back causing
injury.
28. Transport Nailer safely. Always disconnect air supply when moving the tool in the
workplace. Carry the tool by the handle and avoid contact with the trigger.
Note: Performance of the compressor (if powered by line voltage) may vary depending on
variations in local line voltage. Extension cord usage may also affect tool performance.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur.It must be understood
by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 4
Unpacking
When unpacking, check to make sure the parts listed on page 9 are included. If any
parts are missing or broken, please call Harbor FreightTools at the number on the cover of this
manual as soon as possible.
Operation
For best service, you should incorporate an oiler, regulator, and inline filter, as shown in
the diagram below. Hoses, couplers, oilers, regulators, and filters are all available at Harbor
Frei
Note: To connect this tool, we recommend a quick coupler/adapter (not included). Coupler/
adapters are available at Harbor FreightTools.For smoother operation, put 3-5 drops of
pneumatic tool oil in the Air Inlet (122) before each use.
Testing the DoubleTrigger Safety Mechanism
Warning: Even though the nailer should be
Figure 1
empty during this procedure, ALWAYS point
the nailer at a piece of scrap wood when
testing.
1. Make sure the tool is disconnected from the
power supply.
Trigger (125)
2. Completely empty the magazine of nails.
SafetyTrigger
(123)
3. The Nailer should not fire if the second trigger
is not pulled.
4. Check that the Trigger (125) and the Safety Trigger (123) move freely, without sticking -
see Figure 1.
5. Connect the air supply to the tool at the Air Inlet (122) set at the recommended 60-100
PSI, and not to go over the maximum 100 PSI.
6. Hold the tool against the workpiece. Squeeze the Safety Trigger (123) and release it.
The Safety Trigger should return to its original position. Squeeze the Trigger (125). The
tool should not cycle (fire). If it cycles (fires), stop immediately and take the tool to an
authorized service technician.
7. Squeeze the Safety Trigger (123) and then the Trigger (125). The tool must cycle (fire).
If it fails to cycle (fire), take it to an authorized service technician.
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 5
Loading Staples
ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN
RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other
people in the work area must also wear ANSI approved impact safety goggles.
Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool.
1. The Nailer/Stapler should be in the same position as in Figure 2.
2. As in Figure 3, depress Magazine Lock (229) and slide Magazine Cover (227) open.
3. Slide the staples over the Magazine’s Core (216) (see Figure 4).
4. After the staples reach the nose of the tool, close the Magazine Cover (see Figure 5).
Figure 2
Figure 3
Magazine
Lock (229)
Magazine
Cover (227)
Figure 4
Figure 5
Magazine
Cover (227)
Core (216)
Loading Brad Nails
ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN
RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other
people in the work area must also wear ANSI approved impact safety goggles.
Warning! Make sure the Nailer is not attached to
the air hose whenever loading the tool.
Figure 6
1. Follow Loading Staples steps 1 and 2, above.
2. Insert the Brad Nails into the Magazine, letting the
pointed end ride on the rail along the bottom of
the Magazine (205) (see Figures 4 and 6).
Magazine
Cover (227)
3. After the Nails reach the nose of the tool, close
the Magazine Cover (227) (see Figure 6, below).
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 6
Operating the Nailer
1.
2.
Attach the Nailer to the air supply at the Air Inlet (122). Start your compressor and check
the pressure making sure it is set at the recommended 60-100 PSI and not to go over the
maximum 100 PSI.
To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the
Safety Trigger (123) is not depressed. Once depressed, gently and briefly squeeze the
Trigger (125) once. Do not fire repeatedly. Nails could bounce off of one another,
damaging the work piece or causing PERSONAL INJURY.
Figure 7
Note: When using Brad Nails, the Driver Guide (206) might leave a slight
mark on the surface of the workpiece which is larger than the nail
brad. It occurs normally because the Driver Guide (206) tip is
slightly wider to accomodate staples.
To help avoid this, angle the tool slightly as shown in Figure 7.
Anytime any maintenance or repairs are done (including clearing jams), FIRST:
1. Disconnect the Nailer from the air hose.
2. Empty the Magazine (205) completely.
3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of firing any brads.
4. Always leave the Magazine Cover (227) open during maintenance. The Magazine
is spring-loaded and may cause parts or a nail to fly out of the Nailer.
Clearing Jams
Figure 8
1. Disconnect tool from air hose, empty the Magazine
(205) of nails, release any built-up air pressure, and
leave the magazine open, as explained above.
2. While doing this step and the next, hold the Nailer
pointed away from you and any other people or
fragile objects - see Figure 8. Loosen both Cover
Hex Bolts (234) on Driver Guide Cover C (233) 3/4
of a turn each - see Figure 9.
Figure 9
hole
3. Slide Driver Guide Cover C (233) toward the nose
of the Nailer slightly until the holes (See Figure 9.)
in Driver Guide Cover C (233) line up with the heads
of both Cover Hex Bolts (234).
4. Carefully remove Driver Guide Cover C (233) and
remove the jammed nail. Pliers may be necessary
to remove a stuck nail.
Cover Hex
Bolt (234)
Driver Guide
Cover C (234)
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 7
Clearing Jams (continued)
5. Inspect the Driver (114) for bends or breakage - see
Figure 10. If it is not fully retracted or damaged, do
not use the tool until it is repaired by a qualified
technician.
Figure 10
6. Lightly oil the Driver (114) and replace Driver Guide
Cover C (233). Slide Driver Guide Cover C (233)
away from the nose of the Nailer until the shafts of
the Cover Hex Bolts (234) fit into the slots in the
Cover. Tighten both Cover Hex Bolts (234) securely.
Driver (114)
7. Reload the Nailer.
8. Reconnect the Nailer to the air hose.
9. Press the nose of the Nailer against an appropriate piece of scrap wood.
10. Test fire the Nailer several times, checking for proper operation.
11. Disconnect the Nailer, remove the nails and store Nailer in a location out of children’s
reach.
Anytime any maintenance or repairs are done, FIRST:
1. Disconnect the Nailer from the air hose.
2. Empty the Magazine (205) completely.
3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of firing any brads.
4. Always leave the Magazine Cover (227) open during maintenance. The Magazine
is spring-loaded and may cause parts or a nail to fly out of the Nailer.
Maintenance
ANY MAINTENANCE OR REPAIRS ASIDE FROMTHAT LISTED BELOW SHOULD
ONLY BE PERFORMED BY A QUALIFIEDTECHNICIAN.
1. Inspect all of the nuts and screws and make sure they are securely fastened.
2. Periodically lubricate the driving mechanism and magazine with a light oil. Wipe down
with a clean cloth.
3. Inspect and clean the Air Filter Regulator and the Air Compressor according to
manufacturer’s instructions.
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 8
Parts List
Description
Pin
Part
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
Description
Hex Sec. Bolt
Spring Washer
Deflector
Spring
Part
124
125
126
127
128
129
130
131
132
134
201
202
203
204
205
206
207
208
209
210
211
212
213
Part
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
Description
Flat Bar
Trigger
Hex Sec. Bolt
Core
Long Pin
Seal
Pusher
Seal
Trigger Valve Head
Trigger Valve Head
O-ring
Link Block
Cap
Pusher Spring
Spring Washer
Nut
O-ring
O-ring
O-ring
Valve Piston
O-ring
Trigger Valve Guide
O-ring
Bracket
Washer
Stopping Ring
Collar
Hex Sec. Bolt
Spring Washer
Stopping Bracket
Nut
Stopper Spring
Stopper
O-ring
Rear Plate
Magazine Cover
O-ring
Driver
O-ring
Magazine
Cylinder
Bumper
Driver Guide
Driver Guide Cover B
Spring Washer
Hex Sec. Bolt
Driver Guide Cover A
Spring
Magazine Lock
Pin
Gun Body
Joint Guide
Hex Sec. Bolt
O-ring
Spring Washer
Hex Sec. Bolt
Driver Guide Cover C
Cover Hex Bolt
Air Inlet
Flat Bar
Safety Trigger
Hex Sec. Bolt
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTO THE BUYERTHAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 9
Assembly Drawing
SKU 44923
For technical questions, please call 1-800-444-3353.
Page 10
|